To extend the range of your present WiFi network, use the Netgear EX7300 Setup. This Nighthawk X4 AC2200 WiFi Mesh Extender connects to your home WiFi and creates a stable wireless network.

Netgear EX7300 X4 AC2200 Manual Configuration

  • Placing the Netgear EX7300 X4 in the same room as your WiFi router is recommended.
  • Connect the range extender’s power supply.
  • Connect your router to the Nighthawk EX7300 AC2200 WiFi Extender.
  • Launch a web browser and log in to your mywifiext.net account.
  • When you first log in, Netgear installation aid appears on the screen.
  • Read the steps on the screen to complete the Netgear AC2200 Setup and Installation.
  • You have now completed the Netgear Nighthawk X4 EX7300 AC2200 setup.

How to Setup a Netgear EX7300 Range Extender Using WPS:

WPS Button Netgear EX7300 Setup ​

  • Nighthawk X4 AC2200 EX7300 Power
  • Place the extension and WiFi router in the same location.
  • When finished, plug your extension into an electrical outlet.
  • Wait for the EX7300’s power LED to turn green.
  • Press the WPS button on the extender.
  • If the Netgear EX7300 Link Status LED lights are white, the link between your router and the extender is good.
  • Move your extender to a different place.
  • Take your WiFi-enabled desktop, laptop, or mobile device to a location with poor WiFi router coverage.
  • Connect your WiFi-enabled gadgets to a larger network.

That completes your Netgear EX7300 Setup with the WPS button.

Netgear EX7300 AC2200 x4 Firmware Update

The following steps will let you update the firmware on your Netgear Nighthawk EX7300 AC2200:

  • Turn on your WiFi range extender to get started.
  • Connect your router to the Nighthawk Netgear EX7300 Ac2200.
  • Launch any web browser after that.
  • Type Mywifiext.net into the address bar and press the enter key.
  • Enter your repeater’s ID and password.
  • Select the Firmware Update option from the settings menu.
  • Click the Check button to finish.
  • To upgrade the firmware if a new version is available, use the yes button.
  • Next, give the Netgear x4 Nighthawk firmware a few minutes to finish updating.

Netgear Nighthawk X4 AC2200 Setup | Netgear EX7300 Setup

Instructions From The Netgear Support Team For Setting Up A New Extender

  • Your Netgear Nighthawk EX7300 AC2200 should be turned on.
  • Put your WiFi extender close to your router.
  • Now connect the Nighthawk Ac2200 to a power outlet.
  • Hold off until the Green Power LED starts to glow.
  • If the power LED is not illuminated, press the power button.
  • Connect your router to a Netgear Nighthawk X4 extension.
  • Open a web browser on a PC or mobile device, and sign up at www.mywifiext.net.
  • The Netgear displays’ installation help.
  • Follow the steps below to connect your extender to an existing WiFi network.
  • Use your extender in a different position.
  • If you don’t receive a connection or it’s a bad connection, move the extender closer to your router and try again before the Link Status LED turns white.
  • After you’ve determined the optimal location for your extender, connect your client devices to the extended WiFi network.

If you’re still having difficulties configuring your Netgear Nighthawk X4 EX7300 AC2200 Extender, contact an expert.

How to reset Netgear EX7300?

The reset technique is often designed to be used when a user forgets his admin password or username. After you reset your Netgear EX7300, it will get your AC2200 ready for a fresh setup process by wiping out any personally identifiable information including passwords, usernames, and SSIDs. You’ll need a toothpick or a paper clip to do a factory reset on your wifi booster.

  • Switch on your EX7300.
  • Grab a paperclip or a toothpick.
  • You can discover the factory reset button in a small hole.
  • With a toothpick or paperclip, press the WPS button for 8 to 10 seconds.
  • The AC2200 will reboot on its own after a little delay.
  • You can now start the new installation process on your Nighthawk X4.

You can reset your Netgear EX7300 in this manner. You can call us at our toll-free number or utilize our live chat function if you still need help at any stage.

Netgear EX7300 | Key Features

Netgear AC2200 improves range by extending 2.4 and 5 GHz WiFi transmissions from existing WiFi routers. WiFi with dual bands up to 2.2 GHz Coverage area of up to 10,000 ft2 MU-MIMO allows you to stream to numerous devices at the same time. Range is increased using high power amplifiers and an integrated antenna array. FastLane technology improves performance across both WiFi bands. Convenient wall-plug design for simple, discrete installation Netgear AC2200 is compatible with any WiFi router.